Match the Audi part number, infotainment option and connector ID to the fitted unit before using these pinouts. Connector illustrations identify the viewing side where the reference specifies it.
MMI and navigation
Audi (2005-2012) A4, A5, A6 MMI basic plus Unit and misc connectors
The drawing and connector IDs below follow the A4 B8 workshop configuration. Verify the build and connector IDs on A5 and A6. Part number 4F0910769F is listed in the index with uncertain fitment.
J523 · MMI Basic Plus main connector
Rear of J523, redrawn from the A4 workshop illustration. A uses positions 1–8 and D uses 9–16 in the upper bank. B is lower left and C is lower right.
The index groups positions 11–16 under A. The Audi workshop illustration identifies those positions as block D.
Block A · T8ab
J523 terminal face, as viewed at the rear of the unit. The outline identifies block A for the table below.
Cavity
Function
1
Wake signal to E380
4
HU reset to E380
5
BT reset to E380
8
Ground to J685 display
Block B · T12q
J523 terminal face, as viewed at the rear of the unit. The outline identifies block B for the table below.
Cavity
Function
1
Data sent to E380
3
Positive data to J685
4
Negative data to J685
5
Data received from E380
Block C · T12r
J523 terminal face, as viewed at the rear of the unit. The outline identifies block C for the table below.
Cavity
Function
5
Negative data from J685
7
Ground to E380
11
Positive data from J685
Block D · upper positions 9–16
J523 terminal face, as viewed at the rear of the unit. The outline identifies block D for the table below.
Cavity
Function
11
Telephone audio mute input
12
Ground, terminal 31
13
Power feed to J685 display
14
Ring-break diagnostics
15
Battery positive, terminal 30
16
Power feed to E380 control panel
J685 display · 10-pin T10t
Rear-of-display view from Audi workshop drawing A91-10052. Pin 1 is upper left and pin 6 is directly below it.
Display power discrepancy. The index lists pin 1, while the A4 B8 workshop manual lists pin 2. Verify the fitted display and wiring diagram before applying power.
Cavity
Function
2
Display power from J523, per Audi A4 workshop manual
3
Ground from J523
6
Ground, terminal 31
7
Positive data from J523
8
Negative data from J523
9
Positive data to J523
10
Negative data to J523
R41 MMI CD changer · 8-pin electrical connector
R41 electrical connector, drawn in the numbering orientation shown in the MMI Basic Plus reference.Rear view from the Audi Q5 R41 service illustration A91-12116, showing the recess around the purple electrical socket.
Cavity
Function
1
Ground, terminal 31
2
Battery positive, terminal 30
4
Ground, listed for MMI Basic only
5
Ring-break diagnostics
E380 multimedia controls · 16-pin T16c
Audi workshop drawing A91-0908, viewed into the E380 socket. Pin 1 is upper left and pin 9 is directly below it.
Cavity
Function
6
Wake signal
7
Power supply
8
Ground
13
HU reset
14
BT reset
15
Data input
16
Data output
Audi A6/S6/RS6 C5 and A4 · RNS-E Navigation Plus
Aisin RNS-E · Audi A6/S6/RS6 C5 part 4B0 035 192 P (Aisin 86113-60V110). The photographed factory label for A4 part 8E0 035 192 Q shows the same assignments. Match the suffix on the installed radio. Separate R8 and TT radios have their own part numbers.
Assignments for both part numbers follow the Aisin radio labels. Terminal 30 is D15 and terminal 31 is D12. DSP wake at D13, the CD-changer supply and the 32-way analogue inputs have separate functions. Only labelled signals are listed.
RNS-E housing in the factory label orientation (rotated 180°).
A · front speakers
RNS-E socket viewed from the rear of the radio · block A.
Cavity
Function
2
Right front speaker +
3
Left front speaker +
6
Right front speaker −
7
Left front speaker −
B · CD changer and external control
RNS-E socket viewed from the rear of the radio · block B.
Cavity
Function
1
MOST ring-break signal
2
CD changer audio ground
3
Vehicle-speed signal
4
CD changer supply (U14R-2)
5
K-line diagnostics
6
CD changer data out
7
BOSE coding
8
CD changer left audio input
9
CD changer right audio input
10
CD changer switched supply (U14 ST CDC)
11
CD changer data in
12
CD changer clock
C · line output, telephone and microphone
RNS-E socket viewed from the rear of the radio · block C.
Cavity
Function
1
Microphone input −
2
Reverse signal (RFSL)
3
Front left line output
4
Microphone output −
5
Rear left line output
6
Telephone audio input −
7
Microphone input +
8
Line-output ground
9
Front right line output
10
Microphone output +
11
Rear right line output
12
Telephone audio input +
D · power, CAN and amplifier control
RNS-E socket viewed from the rear of the radio · block D.
Part numbers listed: 4L0035646 (minimal), 4L2035670G, 8R1035670M (maximal)
Variant check. The Block A source repeats cavity 6 with reset descriptions. Confirm the reset wiring on the applicable minimum, intermediate or maximum equipment version. A single listed description is shown as supplied where the source gives no separate option values.
16 pin A connector
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Minimum
Intermediate
Maximum
Single source assignment
1
LF mute from preliminary setup for cell phone preparation
N/C
LF mute from preliminary setup for cell phone preparation
—
2
—
—
—
Voltage supply to Multimedia Control Head
3
—
—
—
Wake UP to multimedia system control head
5
N/C
N/C
Switch-on signal for the Cellular Telephone Amplifier
—
6
—
—
—
Reset to the Multimedia System Control Head
7
—
—
—
Ring-break diagnostic cable
9
N/C
N/C
Switch-on signal to Telephone Baseplate
—
10
—
—
—
Data from multimedia system control head
11
—
—
—
Data to the multimedia system control head
12
—
—
—
Ground (terminal 31)
13
N/C
N/C
DIAG signal from Telephone Baseplate
—
14
—
—
—
Reset from multimedia system control head
15
—
—
—
Permanent power (terminal 30)
16
—
—
—
Ground (GND) to multimedia system control head
12 pin B connector (blue)
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Minimum equipment
Higher equipment
2
—
Microphone IN (+) for the microphone unit in front roof module (Right)
3
—
Microphone IN (-) for the microphone unit in front roof module (Right)
5
—
CVBS wire (-) from Rear View Camera System Control Module
8
Microphone IN (+) for the microphone unit in front roof module
Microphone IN (+) for the microphone unit in front roof module (Left)
9
Microphone IN (-) for the microphone unit in front roof module
Microphone IN (-) for the microphone unit in front roof module (Left)
11
—
CVBS wire (+) from Rear View Camera System Control Module
12 pin C connector (green)
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
LF-In ground
2
Right LF-In
3
USB (+5V)
4
USB (ground)
6
Detect
7
Left LF-In
8
LF-In ground shielding
9
CVBS cable (+)
10
CVBS cable (-)
11
iPod data
12
iPod data
4 pin display unit Connector
Audi Q5 8R J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Display pin 2 varies. T4al uses LIN on the documented configuration. Audi lists pin 2 as unused on the grey T4am configuration.
Cavity
Function
1
LVDS (-)
2
LIN
3
LVDS(+)
4
ground
4 pin USB Connector
Audi Q5 8R J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D+
2
iPod detected
3
D-
4
ground
Audi (2008-2015) RNS-E A3, TT Navigation Head unit
Part numbers listed: 8J0035193F, 8J0035193FX, 8P0035192S?
Connector block A
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
A9
CAN Bus High (Infotainment)
A10
CAN Bus Low (Infotainment)
A11
NF mute (audio) from pre-fitted components for mobile phone installation
A12
Ground (terminal 31)
A13
Switched positive to digital sound package control unit
A15
Permanent power (terminal 30)
Connector block B
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
B2
Signal ground to CD changer / iPod holder
B4
Permanent live to CD changer / iPod holder
B6
Data output to CD changer / iPod holder
B7
BOSE coding to ground
B8
Signal (left-side) from CD changer / iPod holder
B9
Signal (right-side) from CD changer / iPod holder
B10
Switched positive to CD changer / iPod holder
B11
Data input from CD changer / iPod holder
B12
CLK (clock) from CD changer / iPod holder
Connector block C
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
C1
Microphone input (–) from microphone unit in front roof module
C3
Signal (front left) to digital sound package control unit
C4
Microphone output (–) to telephone transmitter and receiver unit / pre-fitted components for mobile phone installation
C5
Signal (rear left) to digital sound package control unit
C6
NF– (audio) from telephone transmitter and receiver unit / pre-fitted components for mobile phone installation
C7
Microphone input (+) from microphone unit in front roof module
C8
Signal ground to digital sound package control unit
C9
Signal (front right) to digital sound package control unit
C10
Microphone output (+) to telephone transmitter and receiver unit / pre-fitted components for mobile phone installation
C11
Signal (rear right) to digital sound package control unit
C12
NF + (audio) from telephone transmitter and receiver unit / pre-fitted components for mobile phone installation
RNS-E 32-pin AV/TV input connector
Harness insert, wire-entry view with the grey lever shell removed. The installation drawing identifies pin 1 at the lower right in this orientation.
Cavity
Function
6
Analog input · right-side (audio) from connection for external audio sources
13
Audio input, right from TV tuner
14
Screen ground from TV tuner
15
Video input sync. from TV tuner
16
Video input, green from TV tuner
21
Analog input · ground (audio) from connection for external audio sources
22
Analog input · left-side (audio) from connection for external audio sources
28
Audio ground from TV tuner
29
Audio input, left from TV tuner
30
Video ground from TV tuner
31
Video input, blue from TV tuner
32
Video input, red from TV tuner
Audi (2008-2016) A4, A6, S6 C6 4F CD Navigation Basic Unit
Part numbers listed: 4F0035769B, 4F0035769
16 pin A connector
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Wake UP to Multimedia System Control Head
4
Res HU to multimedia system control head
5
Res BT to multimedia system control head
6
Ground (GND) to multimedia system control head
11
NF mute from preliminary setup for cell phone preparation
12
Ground (terminal 31)
13
Voltage supply for the front information display control head
14
Ring-break diagnostic cable
15
Permanent power (terminal 30)
16
Voltage supply to Multimedia System Control Head
12 pin B connector
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Data to the multimedia system control head
3
Data (+) to Front Information Display Control Head
4
Data (-) to Front Information Display Control Head
5
Data from multimedia system control head
12 pin C connector
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
5
Data (-) from Front Information Display Control Head
7
Ground (GND) to Multimedia Control Head
11
Data (+) from Front Information Display Control Head
Audi (2008-2016) A4, S4 8K MMI Navigation Head Unit
minimum and maximum equipment
16 pin A connector
Audi J794 connector orientation. The upper 1–16 bank includes Audi blocks A (1–8) and D (9–16). Check the fitted specification.
Cavity
Minimum equipment
Maximum equipment
1
NF mute from preliminary setup for cell phone preparation
NF mute from preliminary setup for cell phone preparation
2
Voltage supply to Multimedia Control Head
Voltage supply to Multimedia Control Head
3
Wake UP to multimedia system control head
Wake UP to multimedia system control head
5
—
Switch-on signal for the cellular telephone amplifier
6
Res MU to multimedia system control head
Res MU to multimedia system control head
7
Ring-break diagnostic cable
Ring-break diagnostic cable
9
—
Switch-on signal to telephone base plate
10
Data from multimedia system control head
Data from multimedia system control head
11
Data to the multimedia system control head
Data to the multimedia system control head
12
Ground (terminal 31)
Ground (terminal 31)
13
—
Telephone base plate DIAG signal
14
Res BT from multimedia system control head
Res BT from multimedia system control head
15
Permanent power (terminal 30)
Permanent power (terminal 30)
16
Ground (GND) to multimedia system control head
Ground (GND) to multimedia system control head
12 pin B connector
Audi J794 connector orientation. The lower inserts are B on the left and C on the right. Check the fitted specification.
Cavity
Minimum equipment
Maximum equipment
2
—
Microphone IN (+) for the microphone unit in front roof module
3
—
Microphone IN (-) for the microphone unit in front roof module
5
—
FBAS wire (-) from Rear View Camera System Control Module
8
Microphone IN (+) for the microphone unit in front roof module (left front microphone)
Microphone IN (+) for the microphone unit in front roof module (left front microphone)
9
Microphone IN (-) for the microphone unit in front roof module (left front microphone)
Microphone IN (-) for the microphone unit in front roof module (left front microphone)
11
—
FBAS wire (+) from Rear View Camera System Control Module
12 pin C connector
Audi J794 connector orientation. The lower inserts are B on the left and C on the right. Check the fitted specification.
Cavity
Function
1
LF-In ground
2
Right LF-In
3
USB (+5V) to the internet access control module (2013 year or later)
4
USB (ground)
6
Detect to the internet access control module (2013 year or later)
7
Left LF-In
8
LF-In ground shielding
9
FBAS wire (+)
10
FBAS wire (-)
11
iPod data
12
iPod data
4 pin display unit Connector (purple)
Audi A4 B8 J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Display pin 2 varies. T4al uses LIN on the documented configuration. Audi lists pin 2 as unused on the grey T4am configuration.
Cavity
Function
1
LVDS (-)
2
LIN
3
LVDS(+)
4
ground
4 pin USB Connector (yellow)
Audi A4 B8 J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D+
2
iPod detected
3
D-
4
ground
Audi (2011-2014) A6, C7 Low MMI Navigation
Part numbers listed: 4G0035192H, 4G0035192F
52-position main housing · block A
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block A is highlighted.
Cavity
Function
A1
rear right speaker +
A2
front right speaker +
A3
front left speaker +
A4
rear left speaker +
A5
rear right speaker –
A6
front right speaker –
A7
front left speaker –
A8
rear left speaker –
A9
Subwoofer (+)
A10
Centre speaker (+)
A13
Subwoofer (-)
A14
Centre speaker (-)
A17
Ground (terminal 31)
A18
Permanent power (terminal 30)
52-position main housing · block B
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block B is highlighted.
Cavity
Function
B1
Data from multimedia system operating unit
B2
RES BT multimedia system operating unit
B4
Microphone input (+) from microphone unit in front roofmodule, front left microphone
B5
FBAS wire (-) from reversing camera system control unit
B6
DIAG signal from telephone bracket
B7
Data to multimedia system operating unit
B8
Wake-up multimedia system operating unit
B9
Res HU to multimedia system operating unit
B11
FBAS wire (+) from reversing camera system control unit
B12
Microphone input (–) from microphone unit in front roof module front left microphone
52-position main housing · block C
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block C is highlighted.
Cavity
Function
C1
Analog input · ground (audio)
C2
Analog input · right-side (audio)
C3
USB (+5 V)
C4
USB (ground)
C6
Detect
C7
Analog input · left-side (audio)
C8
Analog input · screen ground (audio)
C9
FBAS wire (+)
C10
FBAS wire (–)
C11
iPod data
C12
iPod data
52-position main housing · block E
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block E is highlighted.
The A6 4G RMC service table lists the ring-break circuit at E7. Confirm E12 with the wiring diagram for the fitted telephone equipment.
Cavity
Function
E7
Ring-break diagnostics
E12
Switch-on signal to telephone bracket
4 pin light-brown connector
Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D (+)
2
iPod detected
3
D (–)
4
ground
4 pin purple connector
Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
3
Wake-up to multimedia system operating unit
5
Switch-on signal to aerial amplifier for mobile telephone
6
Res MU to multimedia system operating unit
7
Ring-break diagnostics
9
Switch-on signal to telephone bracket
10
Data from multimedia system operating unit
11
Data to multimedia system operating unit
12
Terminal 31 (ground)
13
DIAG signal from telephone bracket
14
Res BT from multimedia system operating unit
15
Permanent power (terminal 30)
12 pin B connector
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
2
Microphone input (+) from microphone unit in front roof module (front right microphone for LHD vehicle)
3
Microphone input (–) from microphone unit in front roof module (front right microphone for LHD vehicle)
5
FBAS wire (-) from reversing camera system control unit
8
Microphone input (+) from microphone unit in front roof module (front left microphone for LHD vehicle)
9
Microphone input (–) from microphone unit in front roof module (front left microphone for LHD vehicle)
11
FBAS wire (+) from reversing camera system control unit
12 pin C connector
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Analog input · ground (audio)
2
Analog input · right-side (audio)
3
USB (+5V)
4
USB (ground)
5
iPod (ACC power)
6
Detect
7
Analog input · left-side (audio)
8
Analog input · screen ground (audio)
9
FBAS wire (+)
10
FBAS wire (–)
11
iPod data
12
iPod data
4 pin display unit Connector
Audi A8 4H J794 display port. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
LVDS (-)
2
LIN
3
LVDS(+)
4
ground
4 pin USB Connector
Audi A8 4H J794 external audio port. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D+
2
iPod detected
3
D-
4
ground
Audi (2011-2020) A6 RMC plus (LOW II) unit
Part numbers listed: 4G0035188EX, 4G0035188D
52-position main housing · block A
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block A is highlighted.
Cavity
Function
A1
rear right speaker +
A2
front right speaker +
A3
front left speaker +
A4
rear left speaker +
A5
rear right speaker –
A6
front right speaker –
A7
front left speaker –
A8
rear left speaker –
A9
Subwoofer (+)
A10
Centre speaker (+)
A13
Subwoofer (-)
A14
Centre speaker (-)
A17
Ground (terminal 31)
A18
Permanent power (terminal 30)
52-position main housing · block B
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block B is highlighted.
Cavity
Function
B1
Data from multimedia system operating unit
B2
RES BT multimedia system operating unit
B4
Microphone input (+) from microphone unit in front roofmodule, front left microphone
B7
Data to multimedia system operating unit
B8
Wake-up multimedia system operating unit
B9
Res HU to multimedia system operating unit
B12
Microphone input (–) from microphone unit in front roof module front left microphone
52-position main housing · block C
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block C is highlighted.
Cavity
Function
C1
Analog input · ground (audio)
C2
Analog input · right-side (audio)
C3
USB (+5 V)
C4
USB (ground)
C6
Detect
C7
Analog input · left-side (audio)
C8
Analog input · screen ground (audio)
C9
FBAS wire (+)
C10
FBAS wire (–)
C11
iPod data
C12
iPod data
52-position main housing · block E
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block E is highlighted.
Cavity
Function
E7
Ring-break diagnostics
4 pin light-brown connector
Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D (+)
2
iPod detected
3
D (–)
4
ground
4 pin purple connector
Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
LVDS (–)
2
LIN
3
LVDS (+)
4
ground
Audi (2011-2020) A6, S6, A7, S7 3G (3G+) High Satnav MMI Unit
Part numbers listed: 4G0035670
Audi’s 2012 A6 MMI Navigation Plus service drawing shows a 40-position J794 housing. The upper bank spans Audi blocks A and D.
40-position J794 housing · block A/D
Rear socket face, redrawn from the Audi A6 4G Navigation Plus service view. Table A1–A16 spans two service blocks, A (1–8) and D (9–16).
Cavity
Function
A3
Wake-up to multimedia system operating unit
A5
Switch-on signal to telephone bracket / aerial am‐plifier for mobile telephone
A6
Res MU to multimedia system operating unit
A7
Ring-break diagnostics
A9
Switch-on signal to telephone bracket
A10
Data from multimedia system operating unit
A11
Data to multimedia system operating unit
A12
Ground (terminal 31)
A13
DIAG signal from telephone bracket
A14
Res BT from multimedia system operating unit
A15
Permanent power (terminal 30)
40-position J794 housing · block B
Rear socket face, redrawn from the Audi A6 4G Navigation Plus service view. The table numbers this insert locally from 1 to 12.
Cavity
Function
B2
Microphone input (+) from front right microphone, microphone unit in front roof module
B3
Microphone input (-) from front right microphone, microphone unit in front roof module
B5
FBAS wire (-) from reversing camera system control unit
B8
Microphone input (+) from front left microphone, microphone unit in front roof module
B9
Microphone input (-) from front left microphone, microphone unit in front roof module
B11
FBAS wire (+) from reversing camera system control unit
40-position J794 housing · block C
Rear socket face, redrawn from the Audi A6 4G Navigation Plus service view. The table numbers this insert locally from 1 to 12.
Cavity
Function
C1
Analog input · ground (audio)
C2
Analog input · right-side (audio)
C3
USB (+5 V)
C4
USB (ground)
C5
iPod, ACC power
C6
Detect
C7
Analog input · left-side (audio)
C8
Analog input · screen ground (audio)
C9
FBAS wire (+)
C10
FBAS wire (–)
C11
iPod data
C12
iPod data
4 pin yellow connector
Audi A6 4G MMI Navigation Plus J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D (+)
2
iPod detected
3
D (–)
4
ground
4 pin gray connector
Audi A6 4G MMI Navigation Plus J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
LVDS (–)
2
LIN
3
LVDS (+)
4
ground
Audi (2012-2016) A5, S5, A4, S4 MMI Navigation Head Unit
Connector identification. Audi’s A4 B8 J794 service drawing and the photographed 8R1-series rear panel show a 40-position main housing. The upper bank spans Audi blocks A and D. Verify microphone assignments for the steering and equipment configuration. Audi lists T12x pin 2 for right microphone positive on the documented LHD build, while the supplied reference lists pin 1.
40-position J794 housing · block A/D
Rear socket face, redrawn from the Audi A4 B8 Navigation service view. Table A1–A16 spans two service blocks, A (1–8) and D (9–16).
Cavity
Function
A1
NF mute
A2
Voltage supply to multimedia system operating unit
A3
Wake-Up to multimedia system operating unit
A5
Switch-on signal to aerial amlifier for mobile telephone
A6
Res MU to multimedia system operating unit
A7
Ring-break diagnostics
A9
Switch-on signal to telephone bracket
A10
Data from multimedia system operating unit
A11
Data to multimedia system operating unit
A12
Ground (terminal 31)
A13
DIAG signal from telephone bracket
A14
Res BT from multimedia system operating unit
A15
Permanent power (terminal 30)
A16
ground to multimedia system operating unit
40-position J794 housing · block B
Rear socket face, redrawn from the Audi A4 B8 Navigation service view. The table numbers this insert locally from 1 to 12.
Cavity
Function
B1
Microphone input (+) from microphone unit in front roof module (front right microphone )
B3
Microphone input (-) from microphone unit in front roof module (front right microphone )
B5
FBAS wire (-) from reversing camera system control unit
B8
Microphone input (+) from microphone unit in front roof module (front left microphone )
B9
Microphone input (-) from microphone unit in front roof module (front left microphone )
B11
FBAS wire (+) from reversing camera system control unit
40-position J794 housing · block C
Rear socket face, redrawn from the Audi A4 B8 Navigation service view. The table numbers this insert locally from 1 to 12.
Audi A4/A5 B8 MMI J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D (+)
2
iPod detected
3
D (–)
4
ground
4 pin grey connector (for display unit)
Audi A4/A5 B8 MMI J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Display pin 2 varies. T4al uses LIN on the documented configuration. Audi lists pin 2 as unused on the grey T4am configuration.
Cavity
Function
1
LVDS (–)
2
LIN
3
LVDS (+)
4
ground
Audi (2013-2016) A3, S3, RS3 8V MMI unit
MOST unit (I8D), p/n 8V0035874B
52-position main housing · block A
Rear socket face, redrawn from the Audi A3 8V J794 service view. Block A is highlighted.
Cavity
Function
A1
rear right speaker +
A2
front right speaker +
A3
front left speaker +
A4
rear left speaker +
A5
rear right speaker –
A6
front right speaker –
A7
front left speaker –
A8
rear left speaker –
A9
Subwoofer (+)
A10
Centre speaker (+)
A13
Subwoofer (-)
A14
Centre speaker (-)
A17
Ground (terminal 31)
A18
Permanent power (terminal 30)
52-position main housing · block B
Rear socket face, redrawn from the Audi A3 8V J794 service view. Block B is highlighted.
Cavity
Function
B1
Microphone input (+) from microphone unit in front roof module (telephone microphone )
B4
NF (+) (audio) from pre-fitted components for mobile phone installation
B5
NF mute
B6
FBAS wire (-) from reversing camera system control unit
B7
Microphone input (–) from microphone unit in front roof module (telephone microphone)
B10
NF (-) (audio) from pre-fitted components for mobile phone installation
B12
FBAS wire (+) from reversing camera system control unit
52-position main housing · block C
Rear socket face, redrawn from the Audi A3 8V J794 service view. Block C is highlighted.
Cavity
Function
C1
Analog input · ground (audio)
C2
Analog input · right-side (audio)
C3
USB (+5 V)
C4
USB (ground)
C5
iPod, ACC power
C6
Detect
C7
Analog input · left-side (audio)
C8
Analog input · screen ground (audio)
C9
FBAS (+)
C10
FBAS (-)
C11
iPod data
C12
iPod data
52-position main housing · block E
Rear socket face, redrawn from the Audi A3 8V J794 service view. Block E is highlighted.
Cavity
Function
E1
CAN bus High to multimedia system operating unit / display unit for front information display and operating unit control unit
E2
Reset to multimedia system operating unit
E3
Ring-break diagnostics
E5
Switch-on signal to telephone bracket
E6
CAN bus High, infotainment
E7
CAN bus Low to multimedia system operating unit / display unit for front information display and operating unit control unit
E8
Reset from multimedia system operating unit
E11
Status signal from telephone bracket
E12
CAN bus Low, infotainment
4 pin brown connector
Audi A3 8V J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D (+)
2
iPod detected
3
D (–)
4
ground
4 pin purple connector for display unit
Audi A3 8V J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
LVDS (–)
2
LIN
3
LVDS (+)
4
ground
Audi (2013-2020) A6, S6, A7 RMC unit
Part numbers listed: 4G0035182H ??
52-position main housing · block A
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block A is highlighted.
Cavity
Function
A1
rear right speaker +
A2
front right speaker +
A3
front left speaker +
A4
rear left speaker +
A5
rear right speaker –
A6
front right speaker –
A7
front left speaker –
A8
rear left speaker –
A9
Subwoofer (+)
A10
Centre speaker (+)
A13
Subwoofer (-)
A14
Centre speaker (-)
A17
Ground (terminal 31)
A18
Permanent power (terminal 30)
52-position main housing · block B
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block B is highlighted.
Cavity
Function
B1
Data from multimedia system operating unit
B2
RES BT multimedia system operating unit
B7
Data to multimedia system operating unit
B8
Wake-up multimedia system operating unit
B9
Res HU to multimedia system operating unit
52-position main housing · block E
Rear socket face, redrawn from the Audi A6 4G RMC service view. Block E is highlighted.
Cavity
Function
E7
Ring-break diagnostics
4 pin purple connector
Audi A6 4G RMC J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
LVDS (–)
2
LIN
3
LVDS (+)
4
ground
Audi (2014-2017) A3 8V, S3 MMI Head Unit
Part numbers listed: 8V0035038B
52-position main housing · block A
Rear socket face, redrawn from the Audi A3 8V J794 service view. Block A is highlighted.
Cavity
Function
A1
rear right speaker +
A2
front right speaker +
A3
front left speaker +
A4
rear left speaker +
A5
rear right speaker –
A6
front right speaker –
A7
front left speaker –
A8
rear left speaker –
A9
Subwoofer (+)
A10
Centre speaker (+)
A13
Subwoofer (-)
A14
Centre speaker (-)
A17
Ground (terminal 31)
A18
Permanent power (terminal 30)
52-position main housing · block B
Rear socket face, redrawn from the Audi A3 8V J794 service view. Block B is highlighted.
Cavity
Function
B1
Microphone input (+) from microphone unit in front roof module (telephone microphone )
B4
NF (+) (audio) from pre-fitted components for mobile phone installation
B5
NF mute
B6
FBAS wire (-) from reversing camera system control unit
B7
Microphone input (–) from microphone unit in front roof module (telephone microphone)
B10
NF (-) (audio) from pre-fitted components for mobile phone installation
B12
FBAS wire (+) from reversing camera system control unit
52-position main housing · block C
Rear socket face, redrawn from the Audi A3 8V J794 service view. Block C is highlighted.
Cavity
Function
C1
Analog input · ground (audio)
C2
Analog input · right-side (audio)
C3
USB (+5 V)
C4
USB (ground)
C7
Analog input · left-side (audio)
C8
Analog input · screen ground (audio)
52-position main housing · block E
Rear socket face, redrawn from the Audi A3 8V J794 service view. Block E is highlighted.
Cavity
Function
E1
CAN bus High to multimedia system operating unit / display unit for front information display and operating unit control unit
E2
Reset to multimedia system operating unit
E3
Ring-break diagnostics
E5
Switch-on signal to telephone bracket
E6
CAN bus High, infotainment
E7
CAN bus Low to multimedia system operating unit / display unit for front information display and operating unit control unit
Audi A3 8V J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D (+)
2
iPod detected
3
D (–)
4
ground
4 pin turquoise connector (for display unit)
Audi A3 8V J794 service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
LVDS (–)
2
LIN
3
LVDS (+)
4
ground
Audi (2010-2018) A1 MMI Navi Head Unit
Part numbers listed: 8XA035192A (also for 8X0035183F, 8X0857273B, 8X0035183E?)
The Audi A1 RMC service manual identifies the CAN and MOST variant circuits as block E, T12w.
52-position main housing · block A
Rear socket face, redrawn from the Audi A1 8X Concert RMC service view. Block A is highlighted.
Cavity
Function
A1
rear right speaker +
A2
front right speaker +
A3
front left speaker +
A4
rear left speaker +
A5
rear right speaker –
A6
front right speaker –
A7
front left speaker –
A8
rear left speaker –
A9
Subwoofer in rear shelf
A10
Centre speaker
A13
Subwoofer in rear shelf
A14
Centre speaker
A17
Ground (terminal 31)
A18
Permanent power (terminal 30)
52-position main housing · block B
Rear socket face, redrawn from the Audi A1 8X Concert RMC service view. Block B is highlighted.
Cavity
Function
B4
Microphone input (+) from microphone unit in front roof module (telephone microphone ) (versions with MOST only)
B6
DIAG signal from telephone bracket
B12
Microphone input (–) from microphone unit in front roof module (telephone microphone) (versions with MOST only)
52-position main housing · block C
Rear socket face, redrawn from the Audi A1 8X Concert RMC service view. Block C is highlighted.
Cavity
Function
C1
Analog input · ground (audio)
C2
Analog input · right-side (audio)
C3
USB (+5 V)
C4
USB (ground)
C5
iPod (ACC power)
C6
USB Detect
C7
Analog input · left-side (audio)
C8
Analog input · screen ground (audio)
C9
FBAS wire (+)
C10
FBAS wire (–)
C11
iPod data
C12
iPod data
Block E · T12w CAN/MOST variant
Rear socket face, redrawn from the Audi A1 8X Concert RMC service view. Block C is highlighted.
Cavity
Function
E1
CAN Bus Low (Infotainment)
E7
CAN bus High (Infotainment) OR Ring-break diagnostics (versions with MOST only)
E12
Switch-on signal for telephone bracket /aerial amplifier for mobile telephone (versions with MOST only)
4-pin external media port
Audi A1 8X RMC service view, MOST equipment only. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
D (+)
2
iPod detected
3
D (–)
4
ground
4-pin display port
Audi A1 8X RMC service view. Numbered socket face in the orientation shown in the service information. Match the molded key and connector ID to the fitted unit.
Cavity
Function
1
LVDS (–)
2
LIN
3
LVDS (+)
4
ground
Amplifiers
Audi (2005-2008) A4, S4, RS4 amplifier
Part numbers listed: 8E5035223, 8E5035223D
23-pin amplifier connector
Amplifier socket, viewed from the mating side. The chamfered end is on the left and the middle row ends before the rightmost column.
Cavity
Function
1
Right rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
2
Signal ground from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
3
Left rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
9
Positive switched from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
14
Bass speaker (+)
15
Bass speaker (-)
17
speaker, left rear (+)
18
speaker, left rear (-)
20
speaker, right rear (+)
21
speaker, right rear (-)
22
Ground (terminal 31)
23
Permanent power (terminal 30)
Audi (2005-2008) A4, S4, RS4 BOSE Amplifier (32-pin)
Part numbers listed: 8E5035223B, 8E5035223C
32-pin amplifier connector
End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity
Function
1
Permanent power (terminal 30)
2
Ground (terminal 31)
3
Bass speaker (+)
4
speaker, left rear (-)
5
speaker, right rear (+)
6
Positive switched from Radio R / Navigation System with CD Drive Control Module /Radio/Navigation Display Control Module
7
Signal ground from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
13
Inside speaker (-)
14
Inside speaker (+)
15
Bass speaker (-)
16
speaker, left rear (+)
17
speaker, right rear (-)
19
Left front signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
20
Right front signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
21
Left rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
22
Right rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
26
speaker, right rear (-)
27
speaker, right rear (+)
29
Microphone input (+) from Inside Microphone
30
Microphone input (-) from Inside Microphone (-)
31
speaker, left rear (+)
32
speaker, left rear (-)
Audi (2005-2015) Q7 Basic amplifier
Part numbers listed: 4L0035223, 4L0910223
32-pin amplifier connector
End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity
Function
1
Permanent power (terminal 30)
2
Ground (terminal 31)
3
Front left bass speaker (+)
4
Front right bass speaker (+)
6
Front left speaker (+)
7
Front right speaker (+)
8
Rear left speaker (+)
9
Rear right speaker (+)
10
Centre mid-range and treble speaker (+)
15
Front left bass speaker (–)
16
Front right bass speaker (–)
18
Front left speaker (–)
19
Front right speaker (–)
20
Rear left speaker (–)
21
Rear right speaker (–)
22
Centre mid-range and treble speaker (–)
23
Microphone 1 (+) from microphone unit in front roof module
25
NF (+) (audio) from pre-fitted components for mobilephone installation/Japan nav/China nav
27
Ring-break diagnostics
28
Microphone 1 (–) from microphone unit in front roof module
30
NF (–) (audio) from pre-fitted components for mobilephone installation/Japan nav/China nav
Audi (2006-2008) A4, S4, RS4 BOSE amplifier
Part numbers listed: 8H0035223, 8H0035223A
25-pin amplifier connector
BOSE amplifier socket, viewed from the mating side. The upper row is offset by half a contact pitch and the polarizing recess is at right.
Cavity
Function
1
Inside speaker (+)
2
Inside speaker (-)
6
Signal ground from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
7
Right rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
8
Left rear signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
9
Right front signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
10
Left front signal from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
11
Ground (terminal 31)
12
Permanent power (terminal 30)
14
Bass speaker (+)
15
Bass speaker (-)
16
speaker, left rear (-)
17
speaker, left rear (+)
18
speaker, right rear (+)
19
speaker, right rear (-)
20
speaker, left rear (+)
21
speaker, left rear (-)
22
speaker, right rear (+)
23
speaker, right rear (-)
25
Positive switched from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
Audi (2007-2014) TT BOSE amplifier
Part numbers listed: 8J0035223C, 8J0035223D
18-pin amplifier connector
End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity
Function
3
Signal (front left) (+) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
4
Signal (front left) (–) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
5
Signal (rear left) (+) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
6
Signal (rear left) (–) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
11
Signal (front right) (+) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
12
Signal (front right) (–) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
13
Signal (rear right) (+) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
14
Signal (rear right) (–) from radio / navigation system with CD drive control unit / control unit with display for radio and navigation
32-pin amplifier connector
End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity
Function
1
Permanent power (terminal 30)
2
Ground (terminal 31)
3
Front left bass speaker (+)
4
Front right bass speaker (+)
5
Middle speaker (+)
6
Front right speaker (+)
7
Front left speaker (+)
8
Centre mid-range and treble speaker (+)
9
Microphone input (–) from microphone unit in front roof module
10
Microphone input (+) from microphone unit in front roof module
11
Rear left speaker (–)
12
Rear left speaker (+)
13
Rear right speaker (–)
14
Rear right speaker (+)
15
Front left bass speaker (–)
16
Front right bass speaker (–)
17
Middle speaker (–)
18
Front right speaker (–)
19
Front left speaker (–)
20
Centre mid-range and treble speaker (–)
23
Microphone input (screen ground) from microphone unit in front roof module
27
CAN Bus High (Infotainment)
29
Switched positive from radio / control unit with display for radio and navigation / navigation system with CD drive control unit
32
CAN Bus Low (Infotainment)
Audi (2007-2015) Q7 Bang&Olufsen amplifier
Part numbers listed: 4L0035466
32-pin amplifier connector
End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity
Function
1
Permanent power (terminal 30)
2
Ground (terminal 31)
3
Centre mid-range and treble speaker (+)
4
Front left mid-range speaker (–)
5
Front right mid-range speaker (+)
6
Front left treble speaker (–)
7
Front right treble speaker (+)
8
Rear left treble speaker (–)
9
Rear right treble speaker (+)
11
Rear left mid-range speaker (+)
12
Rear left mid-range speaker (–)
13
Rear right mid-range speaker (+)
14
Rear right mid-range speaker (–)
15
Centre mid-range and treble speaker (–)
16
Front left mid-range speaker (+)
17
Front right mid-range speaker (–)
18
Front left treble speaker (+)
19
Front right treble speaker (–)
20
Rear left treble speaker (+)
21
Rear right treble speaker (–)
25
Microphone 1 (–) from microphone unit in front roof module
26
Microphone 2 (–) from microphone unit in front roof module (up to week 21/09)
27
Ring-break diagnostics
30
Microphone 1 (+) from microphone unit in front roof module
31
Microphone 2 (+) from microphone unit in front roof module (up to week 21/09)
32
Digital sound package control unit 2
J525 secondary 32-pin connector · T32f
J525 connector C / T32f, mating face in Audi drawing A91-0983. The upper row starts at pin 1 on the left.
Cavity
Function
8
NF (–) (audio) from Japan nav/pre-fitted componentsfor mobile phone installation (up to week 21/09)
9-16
Digital sound package control unit 2
24
NF (+) (audio) from Japan nav/pre-fitted componentsfor mobile phone installation (up to week 21/09)
25-32
Digital sound package control unit 2
Audi (2007-2015) Q7 BOSE amplifier
Part numbers listed: 4L0035223
32-pin amplifier connector
End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity
Function
1
Permanent power (terminal 30)
2
Ground (terminal 31)
3
Front right speaker (–)
4
Front right speaker (+)
5
Front right bass speaker (+)
6
Front left bass speaker (+)
7
Front left speaker (–)
8
Front left speaker (+)
9
Microphone 1 (–) from microphone unit in front roof module
10
Microphone 1 (+) from microphone unit in front roof module
11
Rear right mid-range speaker (–)
12
Rear right mid-range speaker (+)
13
Rear left mid-range speaker (–)
14
Rear left mid-range speaker (+)
15
Middle speaker (–)
16
Middle speaker (+)
17
Front right bass speaker (–)
18
Front left bass speaker (–)
19
Rear right speaker (–)
20
Rear right speaker (+)
21
Rear left speaker (–)
22
Rear left speaker (+)
23
Microphone 1 (screen) from microphone unit in front roofmodule
24
Microphone 2 (–) from microphone unit in front roof module(up to week 21/09)
25
Microphone 2 (+) from microphone unit in front roof module (up to week 21/09)
29
Ring-break diagnostics
30
NF (–) (audio) from pre-fitted components for mobile phone installation/Japan nav/China nav (up to week 21/09)
31
NF (+) (audio) from pre-fitted components for mobile phone installation/Japan nav/China nav (up to week 21/09)
Audi (2008-2011) A5,A4,Q5 Bang&Olufsen Amplifier (with CAN)
Part numbers listed: 8T0035223AP, 8T0035223AJ
18-pin amplifier connector
End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
End-view redraw from the connector reference matched to this amplifier. Compare the cavity numbers and keying with the installed connector.
Cavity
Function
1
Permanent power (terminal 30)
2
Ground (terminal 31)
4
Rear left bass speaker (+)
5
Rear left bass speaker (-)
6
Centre speaker (-)
7
Front left bass speaker (-)
8
Front left bass speaker (+)
9
Front right bass speaker (+)
10
Front right bass speaker (-)
11
Front left mid-range speaker (–)
12
Front left mid-range speaker (+)
13
Front right mid-range speaker (–)
14
Front right mid-range speaker (+)
16
Rear right bass speaker (–)
17
Rear right bass speaker (+)
18
Centre speaker (+)
19
Subwoofer (–)
20
Subwoofer (+)
21
Subwoofer (+)
22
Subwoofer (–)
23
Front right treble speaker (–)
24
Front left treble speaker (–)
25
Rear left treble speaker (+)
26
Rear right treble speaker (+)
27
Right effect speaker (–)
28
Left effect speaker (–)
29
Microphone input (-) from microphone unit in front roof module, internal microphone
31
Front right treble speaker (+)
32
Front left treble speaker (+)
33
Rear left treble speaker (–)
34
Rear right treble speaker (–)
35
Right effect speaker (+)
36
Left effect speaker (+)
37
Microphone input (+) from microphone unit in front roof module, internal microphone
38
Ring-break diagnostics
CD changer
Audi (2005-2015) CD Changer
Part numbers listed: 8E0057111D
12-pin CD changer connector
CD changer 8E0057111D socket face. The two lower locating tabs match the connector illustration.
Cavity
Function
1
CD data out to Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
2
CD CLK out to Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
3
Ground from Radio R /terminal 31 (with RNS-E/radio generation II+)
4
CD data in from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
6
Permanent positive from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
7
Right signal to Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
8
Positive switched from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
9
Signal ground from Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
10
Left signal to Radio R / Navigation System with CD Drive Control Module / Radio/Navigation Display Control Module
Chorus
Audi TT/TTS 8J · Chorus II+ EU (8J0 035 152 G)
Part 8J0 035 152 G. Audi identifies this suffix as Chorus II+ for the 8J TT family. The drawings follow the photographed Chorus rear socket and the matching label layout. The connector label marks C10 as AU PL and D16 as DI SENS. Their electrical details are unspecified.
Chorus II+ connector in the factory label orientation (rotated 180°).
A · front speakers
Chorus II+ socket viewed from the rear of the radio · block A.
Cavity
Function
2
Right front speaker +
3
Left front speaker +
6
Right front speaker −
7
Left front speaker −
B · CD changer, AUX and BOSE coding
Chorus II+ socket viewed from the rear of the radio · block B.
Cavity
Function
1
AUX left input
2
SDI/CD audio ground
3
AUX audio ground
4
Permanent +12 V supply for CD changer
5
BOSE coding
6
CD changer data out
7
AUX right input
8
SDI/CD left audio input
9
SDI/CD right audio input
10
CD changer switching line (switch symbol on label)
11
CD changer data in
12
CD changer clock
C · line outputs, telephone and diagnostics
Chorus II+ socket viewed from the rear of the radio · block C.
Cavity
Function
3
Front left line output
5
Rear left line output
6
Telephone audio −
7
K-line diagnostics (K-LTG)
8
Line-output ground
9
Front right line output
10
AU PL (as marked on the label)
11
Rear right line output
12
Telephone audio +
D · power, CAN and control
Chorus II+ socket viewed from the rear of the radio · block D.
Cavity
Function
9
Infotainment CAN high
10
Infotainment CAN low
11
Telephone mute
12
Ground
13
DSP enable
14
Alarm line (DWA)
15
Permanent +12 V battery supply
16
DI SENS (as marked on the label)
Audi (2010-2014) A1, S1 Chorus Head Unit
Part numbers listed: 8X0035160
Variant check. The reference lists A4 and A8 as negative speaker circuits with inconsistent channel pairing. Those two assignments require a factory wiring check.
Block A
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
A1
speaker (+) (rear right)
A2
speaker (+) (front right)
A3
speaker (+) (front left)
A4
Assignment requires confirmation
A6
speaker (–) (front right)
A7
speaker (–) (front left)
A8
Assignment requires confirmation
A9
CAN Bus High (Infotainment)
A10
CAN Bus Low (Infotainment)
A12
Ground (terminal 31)
A15
Permanent power (terminal 30)
A16
Permanent live connected to PIN 15 (anti-theft alarm)
Block C
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
C6
NF– (audio) from telephone transmitter and receiver unit
C9
Signal (front right) to digital sound package control unit
C10
NF mute (audio)
C12
NF + (audio) from telephone transmitter and receiver unit
Audi (2010-2017) A4, A5, Q5 Chorus III Head Unit
Part numbers listed: 8R2057152
16 pin connector A (brown and black plugs)
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
RR+ · Right rear speaker (+)
2
FR+ · Right front speaker (+)
3
LF+ · Left front speaker (+)
4
LR+ · Left rear speaker (+)
5
RR- · Right rear speaker (-)
6
FR- · Right front speaker (-)
7
LF- · Left front speaker (-)
8
LR- · Left rear speaker (-)
9
CAN H · CAN Bus high (Infotainment)
10
CAN L · CAN Bus low (Infotainment)
11
DISP_P · Power Supply to Front Information Display Control Head
12
GND · Ground (terminal 31)
13
D_CAN · CAN Bus (Display) to the Front Information Display Control Head
14
D_CAN · CAN Bus (Display) to the Front Information Display Control Head
15
Batt · Permanent power (terminal 30)
12 pin B connector (blue plug)
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Left LF · Left LF-In from the External Audio Source Connection
2
LF GND · LF-In ground from the External Audio Source Connection
3
Ground · Ground
4
Batt+ · Permanent positive
6
DATA OUT
7
Right LF · Right LF-In from the External Audio Source Connection
8
Left · Left signal
9
Right · Right signal
10
ACC+ · Positive switched
11
DATA IN
12
CLK
12 pin C connector (green plug)
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Microphone IN (-)
2
Right LF OUT
3
LF OUT ground
4
Microphone OUT (-)
5
Left LF IN (-)
6
LF (-) · from the cell phone preparation/ Telephone Transceiver
7
Microphone IN (+)
8
Left LF OUT
9
Microphone OUT (+)
10
LF mute · wire from preliminary setup for cell phone preparation
11
Left LF IN (+)
12
LF (+) · from the cell phone preparation/ Telephone Transceiver
Concert
Audi (2002-2008) Concert 2 CD RS4, A6 Head Units
Part numbers listed: 4B0035186H, 4B0057186Q, 4B0035186G, 8N0035186B, 4B0035186Q
A connector (black)
Radio-side 46-pin ISO reference, with block A highlighted.
Cavity
Function
1
BOSE coding to ground (only with BOSE)
2
Anti-theft warning system ground from Comfort System Central Control Module
3
L-diagnostic
7
Permanent power (terminal 30)
8
Ground (terminal 31)
B connector (brown)
Radio-side 46-pin ISO reference, with block B highlighted.
Cavity
Function
3
Right front speaker (+) (not with BOSE)
4
Right front speaker (-) (not with BOSE)
5
Left front speaker (+) (not with BOSE)
6
Left front speaker (-) (not with BOSE)
C connector (black)
Radio-side 46-pin ISO reference, with block C highlighted.
Cavity
Function
1
Left rear signal to Amplifier
2
Right rear signal to Amplifier
3
Signal ground to Radio
4
Left front signal to Amplifier (only with BOSE)
5
Right front signal to Amplifier (only with BOSE)
6
Positive switched to Amplifier
7
CAN-Bus High (Infotainment)
10
CD ground to CD Changer
12
CAN-Bus Low (Infotainment)
13
CD data in from CD Changer
14
CD data out to CD Changer
15
CD CLK from CD Changer
16
Permanent positive to CD Changer
17
Positive switched to CD Changer
18
CD ground to CD Changer
19
Left signal from CD Changer
20
Right signal from CD Changer
D connector (red)
Radio-side 46-pin ISO reference, with block D highlighted.
Cavity
Function
1
NF mute from Telephone Transceiver /preliminary setup for cell phone package
3
NF (+) from Telephone Transceiver (not with Nav IV)/preliminary setup for cell phone package
4
NF (-) from Telephone Transceiver (not with Nav IV)/preliminary setup for cell phone package
5
NF (+) from Navigation System with CD Drive Control Module (only with Nav IV)
6
NF (-) from Navigation System with CD Drive Control Module (only with Nav IV)
7
Navigation control wire from Navigation System with CD Drive Control Module (only with Nav IV)
Audi A4 B7 · Concert Solo (8E0 035 186 AK)
Part 8E0 035 186 AK · Blaupunkt 7 646 136 380. The socket and connector-label views follow the photographed unit. The label marks C10 as AU PL and D16 as DI SENS. Their electrical details are unspecified.
Concert Solo connector in the factory label orientation (rotated 180°).
A · front speakers
Concert Solo socket viewed from the rear of the radio · block A.
Cavity
Function
2
Right front speaker +
3
Left front speaker +
6
Right front speaker −
7
Left front speaker −
B · CD changer, AUX and BOSE coding
Concert Solo socket viewed from the rear of the radio · block B.
Cavity
Function
1
AUX left input
2
SDI/CD audio ground
3
AUX audio ground
4
Permanent +12 V supply for CD changer
5
BOSE coding
6
CD changer data out
7
AUX right input
8
SDI/CD left audio input
9
SDI/CD right audio input
10
CD changer switching line (switch symbol on label)
11
CD changer data in
12
CD changer clock
C · line outputs, telephone and diagnostics
Concert Solo socket viewed from the rear of the radio · block C.
Cavity
Function
3
Front left line output
5
Rear left line output
6
Telephone audio −
7
K-line diagnostics (K-LTG)
8
Line-output ground
9
Front right line output
10
AU PL (as marked on the label)
11
Rear right line output
12
Telephone audio +
D · power, CAN and control
Concert Solo socket viewed from the rear of the radio · block D.
Cavity
Function
9
Infotainment CAN high
10
Infotainment CAN low
11
Telephone mute
12
Ground
13
DSP enable
14
Alarm line (DWA)
15
Permanent +12 V battery supply
16
DI SENS (as marked on the label)
Audi (2008-2012) A4 B8 Concert Head Unit
Part numbers listed: 8T2035186Q, 8R1035186Q, 8T1035186B
Connector block A
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
A1
RR+ · Right rear speaker (+)
A2
RF+ · Right front speaker (+)
A3
LF+ · Left front speaker (+)
A4
LR+ · Left rear speaker (+)
A5
RR- · Right rear speaker (-)
A6
RF- · Right front speaker (-)
A7
LF- · Left front speaker (-)
A8
LR- · Left rear speaker (-)
A9
CAN-H · CAN bus high (Infotainment)
A10
CAN-L · CAN bus low (Infotainment)
A12
GND · Ground (terminal 31)
A15
BAT+ · Permanent power (terminal 30)
A16
Permanent positive (not used)
12 pin B connector
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
B1
Left LF IN+ · Left IN for the external audio source connection
B2
LF GND · LF for the external audio source connection ground
B7
Right LF IN · Right IN for the external audio source connection
12 pin C connector
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
C2
Right LF OUT
C3
LF OUT ground
C4
Microphone OUT (-)
C5
Left LF IN (-)
C6
LF (-) · from Telephone Transceiver
C7
Microphone IN (+)
C8
Left LF OUT
C9
Microphone OUT (+)
C10
LF mute
C11
Left LF IN (+)
C12
LF (+) · for the telephone transceiver
10 pin Front Information Display Connector
Rear of the J685 display in the Audi workshop illustration. Pin 1 is upper right and pin 6 is lower right.
Cavity
Function
1
Voltage Supply
2
Ground
3
n/c
4
Diag. Display
5
Cable Diag
6
LVDS OUT (+)
7
LVDS OUT (-)
8
LVDS OUT ground
9
Diag T0
10
Diag T1
Audi (2008-2014) TT Single CD Concert Radio
Part numbers listed: 8J0035186A, 8J0035186G, 8J0035186P, 8J0035186R
Connector block A
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
A2
speaker (+) (front right) · only with basic sound system
A3
speaker (+) (front left)
A6
speaker (–) (front right)
A7
speaker (–) (front left)
A9
CAN Bus High (Infotainment)
A10
CAN Bus Low (Infotainment)
A11
NF mute (audio) from prefitted components for mobile phone installation
A12
Ground (terminal 31)
A13
Switched positive to digital sound package control unit
A15
Permanent power (terminal 30)
A16
Permanent live connected to PIN 15 (anti-theft alarm)
Connector block B
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
B1
Analog input · left-side (audio)
B2
Signal ground to CD changer / iPod holder
B3
Analog input · ground (audio)
B4
Permanent live to CD changer / iPod holder
B5
BOSE coding to terminal 31 · only with BOSE
B6
Data output to CD changer / iPod holder
B7
Analog input · right-side (audio)
B8
Signal (left-side) from CD changer / iPod holder
B9
Signal (right-side) from CD changer / iPod holder
B10
Switched positive to CD changer / iPod holder
B11
Data input from CD changer / iPod holder
B12
CLK (clock) from CD changer / iPod holder
Connector block C
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
C3
Signal (front left) to digital sound package control unit
C5
Signal (rear left) to digital sound package control unit
C6
NF– (audio) from telephone transmitter and receiver unit
C8
Signal ground to digital sound package control unit
C9
Signal (front right) to digital sound package control unit
C11
Signal (rear right) to digital sound package control unit
C12
NF + (audio) from telephone transmitter and receiver unit
Audi (2010-2016) A4, A5, RS5, Q5 Concert III Head Unit
Part numbers listed: 8T1 035 186R ?
16 pin connector A (brown and black plugs)
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
RR+ · Right rear speaker (+)
2
FR+ · Right front speaker (+)
3
LF+ · Left front speaker (+)
4
LR+ · Left rear speaker (+)
5
RR- · Right rear speaker (-)
6
FR- · Right front speaker (-)
7
LF- · Left front speaker (-)
8
LR- · Left rear speaker (-)
9
CAN H · CAN Bus high (Infotainment)
10
CAN L · CAN Bus low (Infotainment)
12
GND · Ground (terminal 31)
15
Batt · Permanent power (terminal 30)
12 pin B connector (blue plug)
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Left LF · Left LF-In from the External Audio Source Connection
2
LF GND · LF-In ground from the External Audio Source Connection
3
Ground · Ground
4
Batt+ · Permanent positive
6
DATA OUT
7
Right LF · Right LF-In from the External Audio Source Connection
8
Left · Left signal
9
Right · Right signal
10
ACC+ · Positive switched
11
DATA IN
12
CLK
12 pin C connector (green plug)
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Microphone IN (-)
2
Right LF OUT
3
LF OUT ground
4
Microphone OUT (-)
5
Left LF IN (-)
6
LF (-) · from the cell phone preparation/ Telephone Transceiver
7
Microphone IN (+)
8
Left LF OUT
9
Microphone OUT (+)
10
LF mute · wire from preliminary setup for cell phone preparation
11
Left LF IN (+)
12
LF (+) · from the cell phone preparation/ Telephone Transceiver
10 pin Front Information Display Connector
Rear of the J685 display in the Audi workshop illustration. Pin 1 is upper right and pin 6 is lower right.
Cavity
Function
1
Voltage Supply
2
Ground
3
n/c
4
Diag. Display
5
Cable Diag
6
LVDS OUT (+)
7
LVDS OUT (-)
8
LVDS OUT ground
9
Diag T0
10
Diag T1
Displays
Audi (2002-2017) Multimedia Information Display Unit
Part numbers listed: 8F0919604, 8R0919604, 4F0919604, 4L0919604, 4F0919604X, 8R0919604A
T8ai · separate display power
Audi workshop view of the J685 power socket. Cavity 1 is at the right end.
Cavity
Function
4
Battery supply, terminal 30
5
Ground, terminal 31
T4an / T4ao · display link
Audi workshop view. Cavity 1 is lower right and cavity 2 is upper right.
Cavity
Function
1
LVDS negative
2
LIN for the documented A4 B8 configuration
3
LVDS positive
4
Ground
Confirm pin 2 against the exact display part number and build. Some later listings show ground at this position.
Audi (2009-2016) MMI Information Screen 10 pin connector
Black 10-pin connector for the J685 display paired with the Concert or Symphony radio. Check the connector ID before wiring. The red Chorus T10u and the MMI Basic T10t have their own assignments.
Rear of the J685 display in the Audi workshop illustration. Pin 1 is upper right and pin 6 is lower right.Alternate orientation in the connector reference. Pin 1 is upper left. Match the moulded numbers before comparing the two views.
Cavity
Function
1
Power supply from radio
2
Ground
3
Unassigned
4
Display diagnostics
5
Cable diagnostics
6
LVDS positive
7
LVDS negative
8
LVDS ground
9
Diagnostic T0
10
Diagnostic T1
Radio tuner
Audi (2010-2014) A4, S4, A5,A6, Q5, Q7 Radio Receiver Tuner Module
Part number 4G0035082. This section uses the Audi Q5 MMI Radio R service view. Verify equipment and build-specific assignments against the fitted receiver.
Audi numbers the two power terminals above the fuse area as 41 and 42. Some listings refer to them as 17 and 18 within the combined upper bank.
Block A · T8ag
Radio-side view, redrawn from Audi A91-11740. Block A is highlighted. The numbers are the positions on the full housing.
Cavity
Function
1
Rear right speaker (+)
2
Front right speaker (+)
3
Front left speaker (+)
4
Rear left speaker (+)
5
Rear right speaker (−)
6
Front right speaker (−)
7
Front left speaker (−)
8
Rear left speaker (−)
Block D · T16ag
Radio-side view, redrawn from Audi A91-11740. Block D is highlighted. The numbers are the positions on the full housing.
Cavity
Function
9
Rear-shelf subwoofer
10
Centre mid/treble speaker
11
Ring-break diagnostics
13
Rear-shelf subwoofer
14
Centre mid/treble speaker
41
Ground, terminal 31
42
Battery positive, terminal 30
Block B · T12w
Radio-side view, redrawn from Audi A91-11740. Block B is highlighted. The numbers are the positions on the full housing.
Cavity
Function
17
Left audio input
18
Audio input ground
19
Audio input diagnostics
21
Audio diagnostics
22
Telephone low-frequency signal (−)
23
Right audio input
24
Audio input shield ground
27
Telephone audio shield ground
28
Telephone low-frequency signal (+)
Block C
Radio-side view, redrawn from Audi A91-11740. Block C is highlighted. The numbers are the positions on the full housing.
Cavity
Function
29
Headphone output 1 diagnostics
31
Headphone outputs 1 and 2 diagnostics
34
Headphone output 2 diagnostics
35
Headphone output 1 left
36
Headphone output 1 ground
37
Headphone output 1 right
38
Headphone output 2 left
39
Headphone output 2 ground
40
Headphone right output. Verify the channel against the fitted equipment diagram.
Symphony
Audi Symphony II · Panasonic 46-position ISO radio
Panasonic service-manual coverage includes CQ-EA1070L through CQ-EA1074L and CQ-EA1060L through CQ-EA1063L. Documented examples include A4 8E0 035 195, A8 4D0 035 195 H and A6 4B0 035 195 H. This section uses Panasonic's A–D markings. The Audi workshop manual calls the same positions I–IV.
The Panasonic diagram lists a powered antenna output on C5. Some Audi A4 vehicle-side diagrams leave that cavity unassigned. Front speaker outputs on B are used on direct-drive configurations. BOSE uses the external amplifier.
A / I · 20-way audio, CAN and CD changer
Panasonic Symphony II socket face · block A · viewed from the rear of the radio.
Cavity
Function
1
Rear left line output
2
Rear right line output
3
Line-output ground
4
Front left line output
5
Front right line output
6
Switched amplifier output
7
Infotainment CAN high
10
CD changer ground
12
Infotainment CAN low
13
CD changer data in
14
CD changer data out
15
CD changer clock
16
Permanent +12 V supply for CD changer
17
CD changer control output
18
CD changer audio ground
19
CD changer left audio input
20
CD changer right audio input
B / II · 8-way speakers
Panasonic Symphony II socket face · block B · viewed from the rear of the radio.
Cavity
Function
3
Right front speaker +
4
Right front speaker −
5
Left front speaker +
6
Left front speaker −
C / III · 8-way power and diagnostics
Panasonic Symphony II socket face · block C · viewed from the rear of the radio.
Panasonic Symphony II socket face · block D · viewed from the rear of the radio.
Cavity
Function
1
Telephone mute
3
Telephone / navigation audio input +
4
Telephone / navigation audio input −
5
Navigation audio input +
6
Navigation audio input −
7
Navigation audio control
Panasonic’s CQ-JA1070L–CQ-JA1074L service manual identifies those models as Concert radios.
A6 C5 Symphony II SDARS · 4B0 035 195 N
Panasonic CQ-EA1362L. The redraw follows the rear socket of the photographed 4B0 035 195 N unit. The tables list the radio-side positions documented in the 2004 A6 C5 Symphony service material. The front speaker positions are for direct-drive configurations. The SDARS tuner has a separate connector. Use the vehicle-specific wiring diagram to identify any additional BOSE or satellite-radio circuits.
SDARS · A / I · audio, CAN and CD changer
A6 C5 Symphony II SDARS socket face · block A · viewed from the rear of the radio.
Cavity
Function
1
Rear left line output
2
Rear right line output
3
Line-output ground
6
Switched positive for active speaker / amplifier
7
Infotainment CAN high
10
CD changer ground
12
Infotainment CAN low
13
CD changer data in
14
CD changer data out
15
CD changer clock
16
Permanent +12 V supply for CD changer
17
Switched CD changer supply
18
CD changer audio ground
19
CD changer left audio
20
CD changer right audio
SDARS · B / II · direct-drive front speaker positions
A6 C5 Symphony II SDARS socket face · block B · viewed from the rear of the radio.
Cavity
Function
3
Right front speaker +
4
Right front speaker −
5
Left front speaker +
6
Left front speaker −
SDARS · C / III · power and diagnostics
A6 C5 Symphony II SDARS socket face · block C · viewed from the rear of the radio.
Cavity
Function
2
Anti-theft alarm ground
3
Onboard diagnostic line
7
Permanent +12 V battery supply (terminal 30)
8
Ground (terminal 31)
SDARS · D / IV · telephone and navigation
A6 C5 Symphony II SDARS socket face · block D · viewed from the rear of the radio.
Cavity
Function
1
Telephone mute
3
Telephone audio + (vehicles without navigation)
4
Telephone audio − (vehicles without navigation)
5
Navigation audio +
6
Navigation audio −
7
Navigation control
Audi (2005-2008) RS4 and others Symphony II+ Head Unit
Part numbers listed: 8P0057195PX
A connector
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
2
Right front speaker (+) (not with BOSE)
3
Left front speaker (+) (not with BOSE)
6
Right front speaker (-) (not with BOSE)
7
Left front speaker (-) (not with BOSE)
9
CAN-Bus High (Infotainment)
10
CAN-Bus Low (Infotainment)
11
NF mute from preliminary setup for cell phone preparation
12
Ground (terminal 31)
13
Positive switched to Amplifier/Woofer (in left rear luggage compartment) / Amplifier R12
15
Permanent power (terminal 30)
16
Permanent positive connected with PIN 15 (anti-theft warning system)
B connector (blue)
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
2
CD ground to CD Changer
4
Permanent positive to CD Changer
5
BOSE coding to ground (only with BOSE)
6
CD data out to CD Changer
8
Left signal from CD Changer
9
Right signal from CD Changer
10
Positive switched to CD Changer
11
CD data in from CD Changer
12
CD CLK from CD Changer
C connector
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
3
Left front signal to Amplifier (only with BOSE)
5
Left rear signal to Amplifier/Woofer (in left rear luggage compartment) / Amplifier
6
NF (-) from Telephone Transceiver/preliminary setup for cell phone package
8
Signal ground to Amplifier/Woofer (in left rear luggage compartment) / Amplifier
9
Right front signal to Amplifier (only with BOSE)
11
Right rear signal to Amplifier/Woofer (in left rear luggage compartment) / Amplifier
12
NF (+) from Telephone Transceiver /preliminary setup for cell phone package
Audi (2007-2017) Symphony Head Unit
Part numbers listed: 8T1035195AA ?
16 pin connector A (brown and black plugs)
Radio-side 40-pin Quadlock reference, with block A highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
RR+ · Right rear speaker (+)
2
FR+ · Right front speaker (+)
3
LF+ · Left front speaker (+)
4
LR+ · Left rear speaker (+)
5
RR- · Right rear speaker (-)
6
FR- · Right front speaker (-)
7
LF- · Left front speaker (-)
8
LR- · Left rear speaker (-)
9
CAN H · CAN Bus high (Infotainment)
10
CAN L · CAN Bus low (Infotainment)
12
GND · Ground (terminal 31)
15
Batt · Permanent power (terminal 30)
12 pin B connector (blue plug)
Radio-side 40-pin Quadlock reference, with block B highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Left LF · Left LF-In from the External Audio Source Connection
2
LF GND · LF-In ground from the External Audio Source Connection
3
Ground · Ground
4
Batt+ · Permanent positive
6
DATA OUT
7
Right LF · Right LF-In from the External Audio Source Connection
8
Left · Left signal
9
Right · Right signal
10
ACC+ · Positive switched
11
DATA IN
12
CLK
12 pin C connector (green plug)
Radio-side 40-pin Quadlock reference, with block C highlighted. Check the keyed housing and insert colour on the fitted unit.
Cavity
Function
1
Microphone IN (-)
2
Right LF OUT
3
LF OUT ground
4
Microphone OUT (-)
5
Left LF IN (-)
6
LF (-) · from Telephone Transceiver
7
Microphone IN (+)
8
Left LF OUT
9
Microphone OUT (+)
10
LF mute
11
Left LF IN (+)
12
LF (+) · from Telephone Transceiver
10 pin Front Information Display Connector
Rear of the J685 display in the Audi workshop illustration. Pin 1 is upper right and pin 6 is lower right.
Cavity
Function
1
Voltage Supply
2
Ground
3
n/c
4
Diag. Display
5
Cable Diag
6
LVDS OUT (+)
7
LVDS OUT (-)
8
LVDS OUT ground
9
Diag T0
10
Diag T1
TV tuner
Audi (2007-2013) A3, TT, TTS TV Tuner
Part numbers listed: 8J0919148, 8J0919148A, 8J0919148B, 8J0919148C
R78 TV tuner · T54a 54-pin connector
Tuner-side socket viewed into the mating face. Housing details follow the 8J0919148A rear-panel reference. The Audi 54-way service view places 1–18 on the lower row, 19–36 in the middle and 37–54 on top.
Cavity
Function
2
CAN Bus Low (Infotainment)
3
CAN Bus High (Infotainment)
4
Audio screen (front) to navigation system with CD drive control unit
5
Audio output (front right) to navigation system with CD drive control unit
7
Audio output (front left) to navigation system with CD drive control unit
9
Screen ground (front) to navigation system with CD drive control unit
10
Video screen (front) to navigation system with CD drive control unit
11
Video output (Sync., front ) to navigation system with CD drive control unit
12
Video ground to navigation system with CD drive control unit
13
Video output (blue, front ) to navigation system with CD drive control unit
14
Video ground to navigation system with CD drive control unit
15
Video output (green, front ) to navigation system with CD drive control unit
16
Video ground to navigation system with CD drive control unit
17
Video output (red, front ) to navigation system with CD drive control unit
19
Ground (terminal 31)
20
Permanent power (terminal 30)
53
Ext. video ground AV1
54
I/0 pin
Legacy equipment
Audi (2000-2001) Navigation PLUS II Head Unit · Blaupunkt Audi Navigation D2, p/n 4D0 035 192 N
Audi Beta CC · AUZ1Z2 (4A0 035 152) by Blaupunkt 7 640 846 080
Audi Beta CC Autoreverse · AUZ1Z2 (4A0 035 152) by Blaupunkt 7 640 846 080
Audi Beta II
Audi Chorus (Blaupunkt)
Audi Chorus (Grundig)
AUDI Chorus, Concert
Audi Concert AUZ5Z3
Audi Concert CQ-LA1923L
Audi Concert PLUS
Audi Concert US
Audi Delta, Delta CC, Delta CC AUZ1Z4, Delta CC US AUZ1Z6
Audi Gamma car audio connector
Audi Gamma CC · p/n 4A0 035 186
Audi Gamma CC
Audi Gamma CC Bose
Audi Gamma III (M327)
Audi Gamma S
Audi Navigation (2002-2006) disc unit · p/n 4B0 919 887 A, 4B0 919 887 AX, 4B0 919 887 E, 4B0 919 887 EX, 4B0 919 887 C, 4B0 919 887 CX, 4B0 919 887 D, 4B0 919 887 DX
Audi Symphony CQ-JA1920L, CQ-JA1924L Head Units
Audi Symphony EU TT
Audi Symphony HE303
Audi Symphony I
Legacy connector faces and circuit assignments await verification.
Use left/right arrows to navigate the slideshow or swipe left/right if using a mobile device
Choosing a selection results in a full page refresh.
Press the space key then arrow keys to make a selection.